Our warehouse is moving!Ā
29/07 - 11/08/2024 --> No delivery in this period!
Our warehouse is moving!Ā
29/07 - 11/08/2024 --> No delivery in this period!
DA | SB1 | IML | IMD | Lmax | Z | AShear | WBmax | DR1 | RZ | Mat.-No. |
---|---|---|---|---|---|---|---|---|---|---|
20 | 25.9 | 55 | 25 | 105 | 1+1 | 70 | 22.9 | RH | 2.5 | 184379 |
20 | 29.5 | 55 | 25 | 110 | 1+1 | 70 | 26.5 | RH | 2.5 | 184380 |
20 | 33.1 | 55 | 25 | 115 | 1+1 | 70 | 30.1 | RH | 2.5 | 184381 |
25 | 26.5 | 55 | 25 | 105 | 2+2 | 70 | 23.5 | RH | 2.5 | 184382 |
25 | 30.8 | 55 | 25 | 110 | 2+2 | 70 | 27.8 | RH | 2.5 | 184383 |
25 | 48 | 55 | 25 | 130 | 2+2 | 70 | 45 | RH | 2.5 | 184384 |
12 | 13.5 | 45 | 16 | 85 | 1+1 | 70 | 10.5 | RH | 1.5 | 185500 |
12 | 21.5 | 45 | 16 | 90 | 1+1 | 70 | 18.5 | RH | 1.5 | 185501 |
14 | 27 | 50 | 16 | 100 | 1+1 | 70 | 24 | RH | 1.8 | 185502 |
16 | 20.9 | 45 | 16 | 90 | 1+1 | 70 | 17.9 | RH | 2 | 185503 |
16 | 29.6 | 45 | 16 | 100 | 1+1 | 70 | 23.1 | RH | 2 | 185504 |
DA | SB1 | IML | IMD | Lmax | Z | AShear | WBmax | DR1 | RZ | Mat.-No. |
---|---|---|---|---|---|---|---|---|---|---|
20 | 25.9 | 55 | 25 | 105 | 1+1 | 70 | 22.9 | RH | 2.5 | 184379 |
20 | 29.5 | 55 | 25 | 110 | 1+1 | 70 | 26.5 | RH | 2.5 | 184380 |
20 | 33.1 | 55 | 25 | 115 | 1+1 | 70 | 30.1 | RH | 2.5 | 184381 |
25 | 26.5 | 55 | 25 | 105 | 2+2 | 70 | 23.5 | RH | 2.5 | 184382 |
25 | 30.8 | 55 | 25 | 110 | 2+2 | 70 | 27.8 | RH | 2.5 | 184383 |
25 | 48 | 55 | 25 | 130 | 2+2 | 70 | 45 | RH | 2.5 | 184384 |
12 | 13.5 | 45 | 16 | 85 | 1+1 | 70 | 10.5 | RH | 1.5 | 185500 |
12 | 21.5 | 45 | 16 | 90 | 1+1 | 70 | 18.5 | RH | 1.5 | 185501 |
14 | 27 | 50 | 16 | 100 | 1+1 | 70 | 24 | RH | 1.8 | 185502 |
16 | 20.9 | 45 | 16 | 90 | 1+1 | 70 | 17.9 | RH | 2 | 185503 |
16 | 29.6 | 45 | 16 | 100 | 1+1 | 70 | 23.1 | RH | 2 | 185504 |
adjust the tool to run centrally to the workpiece
tools with plunge tip (L4) must project at least 4.5 mm on bottom side of workpiece in order to bring p-System cutting edges into action
for inclined or circular plunge-cutting only
recommended feed rate per tooth (depending on the diameter): wood-based panels 0.2 - 0.3 mm, solid wood 0.15 - 0.2 mm
clamping element: precision clamping element e.g. ps-System, TRIBOS
with thread for length adjusting screw
sense of rotation according to VDMA 8849